Loading... Please wait...Currency Displayed in
- Home
- KNX Products
- Energy & Measurement Monitors
- SK08-AN2 2 Channel Analog Module
Categories
Related Products
-
-
-
-
Arcus Arcus SK08-Ventil4 On-wall 4-Channel KNX Valve Controller 24VDC ¥36,501.70 (inc VAT) ¥30,417.76 (ex VAT)
-
OTOMO OTOMO DALI Module 2 Channels x 8 ECG Broadcast - IO14A01BLE ¥54,386.57 (inc VAT) ¥45,322.14 (ex VAT)
SK08-AN2 2 Channel Analog Module
Hover over image to zoom
Arcus
Product Description
The KNX controller SK08-AN2 is part of the S8 device series and serves to measure two analog voltage values between 0 and 12VDC.
The sensor / controller has two ports, each with a ground, a signal input and a supply voltage pin ( e.g. for a sensor ).
The device has an integrated KNX bus coupler and required, depending on the measurement electronics and configure, an additional voltage between 9 and 30 volts.
The transducer is located in a high-strength, extremely robust stable impact ABS plastic housing. Cover and base have a revolving groove and tongue system with neoprene gasket. The housing is IP54/65.
In the application software there are several controllers available ( two-position or PI controller with continuous or pulsed output ) separately for both channels.
Additional functions include the display of upper and lower thresholds and switching between the set point and threshold.
The sensor is configured by ETS ( Tool Software ) and the application program. Controlling functions such as signal threshold and other adjustments are parameterized by the ETS.
Applications
- Measurement of two analog voltage values between 0 and 10VDC ( e.g. pressure sensors )
- Surveillance and control of chemical and physical measurements, sensor technology with voltage output.
Technical Details
| Measured Value: | Analog voltage |
| Sending Options: | no sending, cyclical sending when change occurs |
| Parameter: | Cyclical sending with variable periods, sending when change occurs with hysteresis |
| Objekttyp S1 .. S2 | 1-Byte unsigned, 1-Byte signed 2-Byte unsigned, 2-Byte signed, 2-Byte float 4-Byte unsigned, 4-Byte signed, 4-Byte float |
| Controller Modi: | Steady PI controller Switched PI controller (PWM) Two-Position controller Two-Position controller Pulsed |
| Parameter Steady PI controller: | Setpoint, reset time, proportional factor, controller mode |
| Parameter Switched PI controller (PWM): | Setpoint, reset time, proportional factor, controller, cycle duration, threshold pitch |
| Parameter Two-Position controller: | Setpoint, differential gap, controller mode |
| Parameter Two-Position controller Pulsed: | Setpoint, differential gap, controller mode , cycle duration, duty cycle |
| Lock Function: | All controller parameterizable as enable or lock |
| Controller Variables Output: | depends on Controller Modi 1-Byte unsigned, 1-Bit Switch |
| Setpoint value send cyclical: | None or 10-250 seconds, parameterizable |
| Limits: pH, ORP, operating time, water temperature: | Lower limit, Upper limit |
| Auxiliary value: | Setpoint, Upper limit or Lower limit |
| Bus power failure: | Saving changed auxiliary quantities, parameterizable |
| Limits S1 .. S2: | Upper limit, Lower limit |
| Auxiliary Value: | Setpoint, Lower limit or Upper limit |
| Bus power failure: | Saving changed auxiliary quantities, parameterizable |
| Measurement range adjustment: | Yes |
| Ambient Temperature Electronic Measuring Equipment Casing: | Operation: -20 .. +55°C Storage: -20 .. +85°C |
| Ambient Humidity: | 0 .. 95% rH not condensating |
| Operating Voltage: | KNX bus voltage 21 .. 32VDC |
| Power Consumption: | approx. 240mW ( at 24VDC ) |
| Auxiliary voltage: | Depending on used measuring electronics 9 .. 30VDC |
| Bus Coupler: | integrated |
| Inbetriebnahme mit der ETS: | ARC_S8.vd5 Produkt: S8-AN2 |
| Curcuit Points: | 2-pole clamps ( red / black ) |
| Protection Class: | IP54/65 |
| Assembly Type Transducer: | Assembly with 2 screws |
| Casing Transducer: | Plastic grey |
| Casing Dimensions: | ( 115 x 65 x 55 ) mm ( L x W x H ) |
| Article number: | 30806202 |